БРАТЬЯ И СЁСТРЫ
ответить на во Вот текст: Drawing consists of pulling metal through a die. One type is wire drawing. The diameter reduction that can be achieved in one die is limited, but several dies in series can be used to get the desired reduction. Sheet metal forming Sheet metal forming is widely used when parts of certain shape and size are needed. It includes forging, bending and shearing. One characteristic of sheet metal forming is that the thickness of the sheet changes little in processing. The metal is stretched just beyond its yield point (2 to 4 percent strain) in order to retain the new shape. Bending can be done by pressing between two dies. Shearing is a cutting operation similar to that used for cloth. Each of these processes may be used alone, but often all three are used on one part. For example, to make the roof of an automobile from a flat sheet, the edges are gripped and the piece pulled in tension over a lower die. Next an upper die is pressed over the top, finishing the forming operation, and finally the edges are sheared off to give the final dimensions. Forging Forging is the shaping of a piece of metal by pushing with open or closed dies. It is usually done hot in order to reduce the required force and increase the metal's plasticity. Open-die forging is usually done by hammering a part between two flat faces. It is used to make parts that are too big to be formed in a closed die or in cases where only a few parts are to be made. The earliest forging machines lifted a large hammer that was then dropped on the workpiece, but now air or steam hammers are used, since they allow greater control over the force and the rate of forming. The part is shaped by moving or turning it between blows. Closed-die forging is the shaping of hot metal within the walls of two dies that come together to enclose the workpiece on all sides. The process starts with a rod or bar cut to the length needed to fill the die. Since large, complex shapes and large strains are involved, several dies may be used to go from the initial bar to the final shape. With closed dies, parts can be made to close tolerances so that little finish machining is required. Two closed-die forging operations are given special names. They are upsetting and coining. Coining takes its name from the final stage of forming metal coins, where the desired imprint is formed on a metal disk that is pressed in a closed die. Coining involves small strains and is done cold. Upsetting involves a flow of the metal back upon itself. An example of this process is the pushing of a short length of a rod through a hole, clamping the rod, and then hitting the exposed length with a die to form the head of a nail or bolt.

Популярно: Английский язык

• 

  albina8427

  31.03.2023 21:50
  Open the brackets using the Present Simple, Present Continuous or...
• 

  zuevbogdan2017

  30.08.2021 21:57
  Change the sentences into reported speech. 1. My sister: «I like shopping)....
• 

  tanamakagonova

  28.04.2020 21:14
  40. I feel nervous. I ve got an exam today, A) Cheer up! Things can...
• 

  опв4

  16.11.2021 01:17
  ни как не могу сделать...
• 

  оля2044

  14.03.2022 16:20
  , очень нужно 1. When I into the office my boss for me. А. сame/ waited...
• 

  елена1229

  02.11.2021 02:33
  Надо существительное превратьть в прилагательное...
• 

  Мучений

  11.03.2020 06:18
  2 ★★ Complete the text with the words in the box. The Romans in Britain....
• 

  кгшкванек1991

  18.08.2020 20:36
  Level 2. Correct the mistakes. 1. Did it cold in the cinema? 2. What...
• 

  VERONIKA75498768783

  23.12.2021 01:41
  The time machine 6 класс 1 задание​...
• 

  amiranur1

  14.04.2022 17:33
  III. Open the brackets: 1. I knew they (to wait) for me at the metro...