БРАТЬЯ И СЁСТРЫ
ответить на во Вот текст: Drawing consists of pulling metal through a die. One type is wire drawing. The diameter reduction that can be achieved in one die is limited, but several dies in series can be used to get the desired reduction. Sheet metal forming Sheet metal forming is widely used when parts of certain shape and size are needed. It includes forging, bending and shearing. One characteristic of sheet metal forming is that the thickness of the sheet changes little in processing. The metal is stretched just beyond its yield point (2 to 4 percent strain) in order to retain the new shape. Bending can be done by pressing between two dies. Shearing is a cutting operation similar to that used for cloth. Each of these processes may be used alone, but often all three are used on one part. For example, to make the roof of an automobile from a flat sheet, the edges are gripped and the piece pulled in tension over a lower die. Next an upper die is pressed over the top, finishing the forming operation, and finally the edges are sheared off to give the final dimensions. Forging Forging is the shaping of a piece of metal by pushing with open or closed dies. It is usually done hot in order to reduce the required force and increase the metal's plasticity. Open-die forging is usually done by hammering a part between two flat faces. It is used to make parts that are too big to be formed in a closed die or in cases where only a few parts are to be made. The earliest forging machines lifted a large hammer that was then dropped on the workpiece, but now air or steam hammers are used, since they allow greater control over the force and the rate of forming. The part is shaped by moving or turning it between blows. Closed-die forging is the shaping of hot metal within the walls of two dies that come together to enclose the workpiece on all sides. The process starts with a rod or bar cut to the length needed to fill the die. Since large, complex shapes and large strains are involved, several dies may be used to go from the initial bar to the final shape. With closed dies, parts can be made to close tolerances so that little finish machining is required. Two closed-die forging operations are given special names. They are upsetting and coining. Coining takes its name from the final stage of forming metal coins, where the desired imprint is formed on a metal disk that is pressed in a closed die. Coining involves small strains and is done cold. Upsetting involves a flow of the metal back upon itself. An example of this process is the pushing of a short length of a rod through a hole, clamping the rod, and then hitting the exposed length with a die to form the head of a nail or bolt.

Популярно: Английский язык

• 

  сафаралиев

  27.12.2021 14:13
  Rewrite the sentences using reported speech 83 ​...
• 

  SviYm

  26.10.2022 02:02
  Рассказ «Перепёлка» ​...
• 

  irina162002

  11.03.2023 03:36
  2. Put the words in the right order and make questions 1) she...
• 

  pandapurple

  09.10.2022 15:40
  Как написать число классная работа на ан​...
• 

  cempalov

  29.10.2021 06:33
  Почему ватсап полезное приложение У МЕНЯ СОР​ на английском но...
• 

  Bohdanka999

  30.04.2021 02:47
  Task 1 Choose the correct item 1 The prince ruled wisely than...
• 

  25durak

  06.05.2020 22:12
  Нужно прочитать текст и дополнить его словами...
• 

  lisa221513

  16.09.2021 14:24
  1I (study) all night yesterday...
• 

  egorovnanastya0

  02.05.2021 09:56
  Look at the posters and listen to the conversation. Which type...
• 

  Оля010720

  27.12.2021 10:15
  с английским В пропусках надо писать gone/been...